Invisible zippers made easy

Invisible zippers made easy

With zipper foot #35

  • How do you sew in an invisible zipper?
  • How do you make sure patterns line up and avoid "bagging" at the bottom?
Zipper foot # 35How do you sew in the zipper?
The advantages of foot #35

The advantages of foot #35


Invisible-zipper foot #35 has two diagonal grooves on the underside of the foot which act as a guide for the zipper coils. These guides unfold the zipper, making it possible to sew close to the coils. After sewing, the zipper folds back again, creating a fantastic invisible zipper!

NOTE 
The instructions in this post are different from the instructions in the video. You can experiment to see which method is better for you.

Measure the length of the zipper

Measure the length of the zipper


First, measure the zipper from the top edge to about 2 cm above the slider. To do this, open it completely and place it onto the edge of the fabric where it will be sewn in afterwards. On the fabric, mark the point to sew up to for the seam below the zipper.

Here, the length of the zipper is 20 cm.

Basting

Basting

Now sew the entire seam using a straight stitch:

  • For the first 20 cm, use a long stitch length, as it will be unpicked again later
  • Secure the seam 
  • Sew the remaining seam using a normal stitch length and secure the end again
  • Then iron the seam allowance open.
Pin onto the seam allowance

Pin onto the seam allowance

To measure the width of the zipper, measure from the folded-up coil to the edge. With a zipper tape width of 1.2 cm and a seam allowance of 2 cm, the outer edge of the zipper is pinned just under one centimeter away from the edge of the fabric. The basted seam sewn with a long stitch is still closed.

Sew onto the seam allowance

Sew onto the seam allowance

The zipper tape is sewn onto the edge of the seam allowance. Jeans foot #8 is very useful for this. Sew as far as you can – as it's not possible to sew past the slider. Secure the end of the seam and sew the other side in the same way.

Open the basting seam

Open the basting seam

Next, unpick the basting seam up to the bartack. Take care not to damage the fabric with the scissors. Depending on the fabric, needle holes can be closed by rubbing with a finger.
Invisible-zipper foot #35

Invisible-zipper foot #35

After attaching foot #35, place the right side of the zipper into the left groove of the zipper foot. The coil slots into the correct position as if by magic.

TIP 
The needle position doesn't usually need adjusting. If the coil on a zipper does not fold up properly, you can change the position. This can happen with zippers from other manufacturers.

If the coil does not unfold by itself, you have to correct the positioning. Sew in the zipper from top to bottom as far as possible and secure the end when you reach the slider.

Sew in the second side in the same way from top to bottom, except that the left side of the zipper goes into the right groove of the foot.
 

Now you just have to pull the slider up through the small opening and close the zipper. You can now marvel at your perfect invisible zipper, with no misalignment or bagging at the bottom.

Perfect invisible zippers are possible - with the right foot!

Picture: Invisible zippers made easy 1/5 Picture: Invisible zippers made easy 2/5 Picture: Invisible zippers made easy 3/5 Picture: Invisible zippers made easy 4/5 Picture: Invisible zippers made easy 5/5

News from the World of BERNINA

Recieve regular news about upcoming events and our BERNINA dealers with the BERNINA newsletter. Simply subscribe to our newsletter to be the first to know about all new offers.

I want to know about new offers and events!

Where would you like to go next?

Tips on starting to sewTips on cleaning and oiling